Hi
When i get my boat it will have a windlass fitted is it best to use 3 strand 10mm rope or multiplat i have never had one so don't know oh and 8mm chain
graham
I think multiplat is better as it beds down well in the anchor locker and does not twist up. You just need to be sure the windlass supports it check on the manufacturers brochure.
Mine does and it works great.
1
- gjb
Thank you
I have multiplat on now so when it arrives I will check lots of new bits to learn about
Allan's been looking at a windlass as well for his boat but from what I have seen in the specs most recommend 3 strand nylon.
Multiplat is nice but expensive and from what I have seen on other boats and my own experience the windlass is not that kind to the rope, so I would save some money and by the 3 strand nylon and replace it when it is worn or frayed.
You may well have to purchase calibrated chain as well, which adds to the overall costs involved.
A lot depends on how you want the anchor to recover and drop. We have only found one make that has an electric free fall to drop the anchor from the cabin. I would steer clear of those which offer a corded remote control as in many cases you will need two hands to deal with the warp and possibly the anchor. Foot controls at the front may well be useful however.
Powered lowering can be painfully slow and many require you to go up front and release the clutch to allow a fast drop, this may not be nice on a sloppy sea state day.
Also I hope you have a good deep anchor well as many state the minimum drop required to prevent a build up of rope and chain in the storage well.
The other thing to consider is a self launch and recovery bow roller and possibly a plate on the bow to protect the gel coat as the anchor comes up out of the water and is swinging about.
Lots to look into, if you can see another craft the same as yours, check out how they have installed the windlass and if possible ask the owner if they have had any issues.
Good luck
Dave
1
- gjb
Redfin came with a windlass and quite honestly it is totally redundant being so slow and cumbersome it is far quicker and easier to use an Alderney ring set up. If you still have the choice I would substitute another toy!
Peter
1
- gjb
How about fitting a capstan, I know some have them.
Not sure if there was a write up from Charlie and the fitment on alfresco, but that seems a great solution to pulling in the Alderney ring and buoy.
Even could be used I guess to pull an anchor that is being dropped from the bow roller.
Dave also has the same winch as alfresco but his has been set up through the rollers and over the bow.
dad also has a smaller windlass on the bow which is for the inshore anchor when playing in studland in the summer, the small windlass can be a pain with the rope getting caught feeding back into the locker, you also have to be on the front with foot controls to stop the chain and anchor hitting the front of the boat, hence why this is rarely used. however it is a great novelty when out with the family when you don't want to run the anchor back onto the deck with young kids around. it also great in tight spaces i.e. the air show as you don't have to run off with the anchor in heavy traffic.
the capstan fitted to the side of the boat with a heavy roller in place is a great addition, yes it is still lifted with an Alderney ring and the traditional method, and if fishing inshore is still normally pulled in by hand by Dan or myself as it is quicker than waiting for the winch.
however when using the larger anchor/heavier chain in deeper water it is a life saver, especially after a day of re anchoring a couple of times.
Alderney method is still by far the most superior method, but this is a creature comfort. if you can afford it why not let machinery take the strain, we do in everything else.
I do agree with rob though in the fact that a capstan would be more useful than a windlass as you are not restricted to a specific setup, you are also safely in the back of the boat if anything does go wrong with no need to go on the bow
hope this helps
sam
3
- Maverick Martin
- gjb
- Stuie
For my boat (Targa 31) a high power windlass is brilliant as it has a walk round deck, there are no safety issues being on the bow. 4 mins to retrieve 100m, I free the clutch to allow the anchor to drop at a fast but controlled rate.
Looking at the photo of a Parker 770 I'm not sure I would want to be walking up to the bow if it cut up rough while at anchor or indeed freeing the clutch for a manual release while dropping anchor. As Dave says using the winch to drop the anchor is very slow, too slow IMO for precision anchoring at the sort of depth's we get round here. I think you would be better off on safety grounds staying in the stern of the boat and use a high power side mounted capstan (if possible), or Alderney ring with a rode run channel to a good quality roller on the bow.
2
- Sam
- gjb
thanks i have always used the Alderney ring so it may be a case of using the windlass for shallow and Alderney ring for deep
graham
I have a 23' Grady White in New Zealand with an anchor winch - which has a rope/chain gypsy using 12m of chain spliced on to 150m of 12mm multi plait, anchoring in depths up to 60m. This has been trouble free from new (7 years) with no chafe etc. This allows me to recover the anchor from the cockpit while on my own and in rough seas. Drop speed is acceptable, but there are not the strong tides that we have to contend with here.
Secret is to make sure the gypsy is well matched to the size of rope and chain, don't skimp on chain and take care to get a good smooth splice to the chain. Occasionally I have to rock the drum a little to get the chain to engage on the gypsy as it changes from rope - and occasionally I have to spread the rope in the anchor locker if it piles up after a deep water anchoring, but this is because I have three times as much warp as the boat builder recommends, so the rope locker is full.
I trip the anchor, happily venture into rough ground, and am still on the original anchor.
Works well for me, although on JV we decided to save the cost of a winch and use an Alderney ring for UK tides and depths. But we would rarely be without a second pair of hands to assist recovery.
Ian
1
- gjb
The fitting of a capstan in the deck area on a craft with walk around sides would be a pain and I suspect a safety issue should you need to get past it in a hurry or in a rough sea.
Boats which don't have this feature capstans seem to work well, however even on some of the newer charter boats have to have a capstan/winch on the bow as they too have walk ways around the cabin especially on some of the cats.
There may also be an issue in getting sufficient reinforcement for the mounting of a windlass as the pull and strain can be considerable especially if the anchor gets stuck!
This is factory fitted so I take that they have made the boat to the standard required to use it , it is not a add on
Graham
I am still in France for the next week or so, but may add to this thread when I get back. Looking at fitting a winch and combined capstan with both on the same side so the rope can go from one to the other if necessary. Some stainless strengthening which Coddie's son may make as he he is setting up his own fabrication/stainless steel/welding business and has access to lazer cutters etc.Will also install a self launching roller, cabin and foot controls etc. It will be side mounted over the anchor well and have about a foot more drop than the Jeanneau factory fitted ones, also, I hope to enlarge the anchor well lid so the rope sits better. Will have to go for slightly larger chain and rope as well.
Its the limited drop into the anchor locker that stops us using the bow capstan in deeper water.
It is a 1kw unit so has power and speed, also a gypsy that takes calibrated chain and rope.
Deeper water we have always used an alderney ring and drifted back to recover the warp and chain, with a 15kg anchor and heavy/long chain its good excercise. So much so that 18 months ago I fitted a side deck capstan.
1.6kw high speed (their words not mine) and a good size drum.
It recovers the anchor warp a treat via the side deck roller, but its far too shiney to wrap chain around in my opinion.
Sure its quicker to haul by hand, but the capstan takes the strain off of the job.
It takes up some deck space, but in my opinion is not a tripping hazard fitted where it is. After all we can always use the other side deck.
Charlie
Allan
The other option I considered was changing my original 9.5mm gypsy to a 7 or 8mm one, then swapping the 10m of 10mm chain to a full 30m length of the much smaller and lighter stuff.
In shallow water I could then use all chain, which would stow better in the anchor locker.
It is the fact that we spend more time in deeper water than shallow, that made my mind up to go for the more expensive side deck option.
Be carefull with the size of cables breakers etc that you need for these units and combined weights. My unit wieghs 24kg and the cables are heavy. All of this weight on the same side of the boat as the helm seat and cooker meant that a few things had to be moved to lockers on the opposite side.
Hope that helps
1
- Leicester Fisheagle
